ImmersionRC Tramp HV 5.8GHz Video TX FPV Transmitter VTX US Version for FPV RC Racing Drone Airplane
ImmersionRC Tramp HV 5.8GHz Video TX FPV Transmitter VTX US Version for FPV RC Racing Drone Airplane
The ImmersionRC Tramp HV 5.8GHz Video Tx is one of the most advanced 5.8GHz Video Transmitter available today. Only 4 grams, and a slender 31 x 20mm, the TrampHV is also a small direct LiPo-powered vTx.
* The USA Version is identical to the International, and EU versions, with one exception. The firmware is region-locked to prevent transmission outside of the USA Ham band. All RaceBand channels are still available, and all power settings are available.
Smallest, Lightest in the Business
Smallest direct LiPo powered vTx in the business.
Traditional button+LED control of frequency and power
All 40 standard channels
Factory power normalization
Micro-power pit mode
Retail regional locking without opening package
Dimensions: L=32mm x W=14mm x H=5mm
Power Output: Programmable, 1mW to > 600mW
RF Impedance: 50 ohms
AV Connector: JST-GH, 6 pin, locking
Audio: Mono, Subcarriers on 6.0 and 6.5MHz (cloned)
Pit Frequency: User/Race Organizer Definable
Power Requirements: 2s-6s HV Lipo
Downloads
The ImmersionRC TrampHV was the first transmitter to support Pit Mode, which was introduced successfully at the FPVAirShow in France. Pit mode transmits a tiny amount of power on a pre-defined frequency to allow for quad setup at a race event without disrupting the show. Pit mode on the TrampHV is a little different than other offerings, being controlled by race directors transparently at drone races. A race director can stay legal by choosing a pit frequency authorized for use at the event, which can be different for events in different regions. Programmed at the event using the Touch’n’Race wand.
Touch ‘n’ Race for Race Directors
Transmitters are placed in Race mode upon arrival at a race event, and remain in that mode until the event is over. Race directors can, without powering up a model, define the frequency and power output of the transmitter, in 5 seconds flat before a race starts.
Why let race directors have all the fun?. The personal TNR wand* avoids dip-switch hell even in the local park. Touch-free programming of video transmitters before you launch, eliminating frequency collisions, eliminating the ‘what channel was I on last’ question, and allowing power levels to be modified between flights to adapt to local conditions. Note that the wand is not required to operate the transmitter. A traditional button + LED user interface may also be used to program channel, band, and power level.
Thermally Protected
The only Video Transmitter in this size and weight class with a fully screened RF deck, providing protection against dust, dirt and knocks, while ensuring smooth sailing through the RTT&E certification process. An optional plastic case can be easily installed to increase this protection even further, without adding excessive size and weight.
LapRF Certified
Another first, introduced by ImmersionRC at FPVAirRace, is technology which allows video transmitters to power up cleanly on their assigned channel without wiping out neighboring channels. Gone are the days when your fellow pilots need to hover safely why you power up beside them. This technology enables asynchronous race starts, where pilots join a race at any time without creating any interference.
Calibrated Power
Each and every TrampHV is factory calibrated to ensure precise power outputs, especially at the critical low-power race levels. No more cross-talk from 25mW transmitters which are instead emitting 200mW!, or worse, 25mW transmitters which emit much lower power levels. No more RF lap timing issues caused by pilots running wildly different power levels.
Package Included
1 x ImmersionRC Tramp HV 5.8GHz Video TX FPV Transmitter VTX US Version for FPV RC Racing Drone Airplane
